Aquaponics pH to 1-Wire Converter – Part 2

This is the first draft of the pH to 1-Wire converter schematic, and some of the component values are still missing. The original circuit runs on 12 VDC, but since the A/D converter IC must be supplied with 5 VDC only I want to scale down the circuit, so that 5 V is the maximum voltage present. I assume I would have to tweak some resistor values in order to make the circuit run at this lower supply voltage, but I haven’t looked into the details yet. I’ll post an updated schematic and the calculations later.

ph_1wire_1.png

(Click on the picture above for a larger version.)

These are the source files:

gEDA schematic, .sch and .pdf:
ph_1wire_1.sch ph_1wire_1.pdf

gEDA symbols, DS2762 and BAT54S:
DS2762-1.sym BAT54S-1.sym

The original idea was to use a 1-Wire A/D converter with built-in 1-Wire digital interface, but the one I found was not recommended for new designs. This is what Maxim writes about the DS2450 A/D converter:

This product is Not Recommended for New Designs. Some versions may be No Longer Available or being discontinued and subject to Last Time Buy, after which new orders can not be placed.

Also known as ‘NRND’. Most of the other A/D converters I found at Maxim had another interface, but the main IC on the soil moisture sensor board from Hobby Boards also converts analog signals to digital and that’s a DS2760. The updated version is called DS2762, which is the one that I have used in the new circuit.

The DS2760 on the soil moisture sensor board measures current, but the IC also has a voltage input pin. The IC is actually a ‘High-Precision Li+ Battery Monitor With Alerts’ as Maxim calls it. The idea is to only use the voltage input pin and 1-Wire interface to get a popular, and cheap, A/D converter, with high input resistance.

Since the DS2762 operates on 5 VDC, the ground reference for the amplifier section should be changed to 2.5 V instead of 7 V in order to use the entire input voltage span of the A/D converter. The 7 V in the original circuit was meant to be measured with a voltage meter and you would have the pH value directly as a reading (pH 7 = 7.00 V, pH 8 = 8.00 V etc.). There’s no meter or display on this new circuit, only data delivered to a computer via the 1-Wire interface, so voltages in the circuit can be converted to something meaningful using software on the computer. Historical data can be displayed with e.g. RRDtool.

When the supply voltage is changed, the gain of the voltage amplifier has to change too, along with a change in offset voltage, i.e. ground reference. IC300 is a dual op-amp IC, where R351, R352 and R355 determines the gain. R300 sets the ground reference voltage level. Apparently it is necessary to put in trimmer resistors, since practical op-amps are not perfect like theoretical ones. Also, the pH probe is worn down as time goes by, and the circuit will have to be calibrated regularly.

Several capacitors have been added to short circuit any fast changing signals as these are irrelevant to aquaponics pH measurements and any alternating currents are considered noise in this respect. It means that the pH values from the 1-Wire interface will need seconds to stabilize. D101 is included to protect the 1-Wire interface.

Since the schematic does not represent the PCB layout, a note has been written about the seemingly long wires going from the BNC connector to the op-amp. On the actual PCB the traces must be as short as possible, because the internal resistance of a pH probe is very high and any electromagnetic radiation will induce relatively high unwanted voltages in the circuit. It shouldn’t be a problem though to place IC300 close to J300.

DS2762 has a general purpose I/O pin (PIO) which can be used for debugging. D100 could be connected to this pin to be able to signal something, but it would probably need an extra transistor. As I want things to be as simple as possible I haven’t included this, but at least there’s a resistor footprint to work with now.

I want to experiment with the values of R351, R353, R354 and R355 in Qucs, as I don’t fully understand the impact of changing the supply voltage, hence the missing resistor values. But I don’t mind – Qucs turns out to be an awesome piece of software for the electronics hacker ;-)

2 thoughts on “Aquaponics pH to 1-Wire Converter – Part 2

  1. What is the motivation behind pot R354? I see how you can set the DC bias with pot R300. Is that just an alternate way to set the bias?

    I have back-burner project to do a fancy version of this using AD5933 impedance analyzer.

    Thanks for posting interesting schematics and notes on them.

    • I don’t know exactly how the network consisting of R351, R353, R354 and R355 works, but it was originally in the design by 66pacific.com, so I’m keeping it for now. I plan on doing a circuit simulation to get a better understanding of how it works, maybe sweep the value of R354. Apparently it’s an offset nulling resistor array, described in The IC Op-amp Cookbook.

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>